Home

href="
TH131 & TH133  
User Guide  
Electronic Thermostat  
2
.
TH131  
Installation  
o
Control Module  
Pilot wire indicator  
Heating indicator  
On/Off switch  
(Europe only)  
Temperature  
selection dial  
TH133  
Power Base  
NOTE: Keep the thermostat's air vents clean and free from obstruc-  
tions.  
3
.
Configuration  
Application Types  
p
3
.1  
Front View  
Rear View  
Type  
Switch Position  
NOTE: Even if the following illustrations show the TH131 model only,  
they can also apply to the TH133 model.  
A
AF  
F
UP (A/AF)  
UP (A/AF)  
DOWN (F)  
1
.
Description  
This user guide covers the following thermostat models:  
n
Position the switch, on the back of the control module, according to  
your application.  
TH131 A/F/AF  
TH133 A/F/AF  
The TH131 model is designed for residential applications, whereas  
the TH133 model is designed for public areas as its controls are hid-  
den and thus protected against unauthorized access. Both models  
can be configured for the following applications:  
Type  
Application  
A
F
Controls the ambient (room) temperature  
3.2  
Minimum and Maximum Limits (TH131 only)  
Use the two potentiometers on the  
back of the control module to set  
the minimum and maximum tem-  
perature limits. Depending on your  
application, the potentiometers  
limit the following temperature:  
Controls the floor temperature  
AF  
Controls the ambient temperature and limits the floor temperature  
notches  
ambient temperature (A)  
floor temperature (F or AF)  
Use a flat-tip screwdriver to rotate  
the potentiometers until the notch  
points to the desired temperature  
limit.  
TH131 & TH133  
400-131-002-C  
1/11/06  
1/2  
href="
4
.
7.  
Operation  
Temperature Adjustment  
Warranty  
;
q
AUBE TECHNOLOGIES INC. THREE (3) YEAR LIMITED WARRANTY  
Aube warrants this product, excluding battery, to be free from defects  
in the workmanship or materials, under normal use and service, for a  
period of three (3) years from the date of purchase by the consumer.  
If at any time during the warranty period the product is determined to  
be defective or malfunctions, Aube shall repair or replace it (at Aube's  
option).  
4
.1  
TH131  
Use the dial on the front of the thermostat to set the desired tempera-  
ture.  
NOTE: If the dial is placed at a temperature beyond the high or low  
temperature limit, the temperature will be maintained at that limit (see  
section 3.2).  
If the product is defective,  
(
i) return it, with a bill of sale or other dated proof of purchase, to  
the place from which you purchased it, or  
TH133  
Remove the control module from the base and use the dial on the  
back of the control module to set the desired temperature.  
(
ii) contact Aube. Aube will make the determination whether the  
product should be returned, or whether a replacement product  
can be sent to you.  
4.2  
On/Off Switch (TH131 only)  
Use the On/Off switch to turn the thermostat Off when it is not used  
This warranty does not cover removal or reinstallation costs. This  
warranty shall not apply if it is shown by Aube that the defect or  
malfunction was caused by damage which occurred while the  
product was in the possession of a consumer.  
(e.g., in the summer).  
5
.
Pilot Wire Orders (Europe only)  
TH131 accepts the six following pilot wire orders when installed on a  
r
Aube's sole responsibility shall be to repair or replace the product  
within the terms stated above. AUBE SHALL NOT BE LIABLE FOR  
ANY LOSS OR DAMAGE OF ANY KIND, INCLUDING ANY  
INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING,  
DIRECTLY OR INDIRECTLY, FROM ANY BREACH OF ANY  
WARRANTY, EXPRESS OR IMPLIED, OR ANY OTHER FAILURE  
OF THIS PRODUCT. Some regions do not allow the exclusion or  
limitation of incidental or consequential damages, so this limitation  
may not apply to you.  
2
30 V power base.  
ORDER  
SIGNAL  
DESCRIPTION  
Comfort  
No signal Maintain temperature at setpoint  
Reduced setpoint  
Maintain temperature at 3.5°C below  
setpoint  
(
3.5k setback)  
THIS WARRANTY IS THE ONLY EXPRESS WARRANTY AUBE  
MAKES ON THIS PRODUCT. THE DURATION OF ANY IMPLIED  
frost protection  
Off  
Maintain temperature at 7°C  
Stop heating  
WARRANTIES,  
INCLUDING  
THE  
WARRANTIES  
OF  
MERCHANTABILITY AND FITNESS FOR  
A
PARTICULAR  
PURPOSE, IS HEREBY LIMITED TO THE THREE-YEAR  
DURATION OF THIS WARRANTY. Some regions do not allow  
limitations on how long an implied warranty lasts, so the above  
limitation may not apply to you.  
1
2
k setback  
k setback  
Maintain temperature at 1°C below setpoint  
Maintain temperature at 2°C below setpoint  
This warranty gives you specific legal rights, and you may have other  
rights which vary from region to region.  
6
.
Specifications  
8
.
s
Customer Assistance  
Setpoint range: 7°C, 15°C to 35°C (45°F, 59°F to 95°F)  
Minimum temperature limit: 5°C to 25°C (41°F to 77°F)  
Maximum temperature limit: 15°C to 35°C (59°F to 95°F)  
Accuracy: ± 0.2°C (0.36°F)  
If you have any questions about the product installation or operation,  
or concerning the warranty, contact us at:  
Storage: -20°C to 50°C (-4°F to 120°F)  
Heating cycle length: 15 minutes  
Software: Class A  
7
05 Montrichard  
10 rue Ampère  
95500 Gonesse  
France  
Tel.: 33 (0) 1 34 07 99 00  
Fax: 33 (0) 1 34 07 99 19  
Email: advaube@comintes.com  
Saint-Jean-sur-Richelieu  
Quebec, Canada J2X 5K8  
Tel.: (450) 358-4600  
Toll Free: 1-800-831-AUBE  
Fax: (450) 358-4650  
Controller: Electronic  
Size (H/W/D):  
Email: aube.service@honeywell.com  
TH131: 78.9 x 78.9 x 16.3 mm (3.1 x 3.1 x 0.64 in.)  
TH133: 78.9 x 78.9 x 18 mm (3.1 x 3.1 x 0.71 in.)  
For more information on our products, go to  
www.aubetech.com  
TH131 & TH133  
400-131-002-C  
1/11/06  
2/2  
href="
PB130  
Installation Instructions  
2
30 V Line Voltage Power Base  
The PB130-230 power base is used to power a TH13x Series control  
module. The resistive load must not exceed 3450 watts (NI) @  
o Before making the connections, make sure  
that the base covers the electrical box  
entirely. If not, install a wall plate at the  
back of the base as shown.  
230 VAC (15 A).  
1
.
Parts  
n
n One (1) PB130-230 power base  
o One (1) floor sensor (for AF and F control modules only)  
p One (1) wall plate (optional, in certain countries)  
p Connect the wires:  
Power:  
2
.
Terminals 1 & 5  
Load:  
Terminals 2 & 4  
see note 1  
Guidelines  
o
Turn off power to the heating system at the main power panel to avoid  
electrical shock. Installation should be carried out by an electrician.  
Pilot Wire:  
Terminal 3  
see note 2  
Floor sensor:  
Terminals 6 & 7  
All work must conform to the applicable country standards for  
electrical installations and wiring.  
This thermostat should be connected on a circuit equipped with  
a fuse or a circuit breaker. It must be installed on a certified  
electrical box.  
(no polarity)  
For a new installation, choose a location about 1.5 m above the  
floor.  
see note 3  
For electric baseboards, convectors and fan-forced heaters, the  
thermostat must be installed facing the heating system.  
The thermostat must be installed on an inside wall.  
Avoid locations where there are air drafts (top of staircase, air  
outlet), dead air spots (behind a door), direct sunlight or  
concealed chimneys or stove pipes.  
Note 1 If a contactor is used between the thermostat and the load,  
install a snubber at the contactor’s coil terminal to ensure  
the proper operation of the thermostat.  
Note 2 This connection is required on some models only.  
3
.
Technical Specifications  
Model: PB130A-230  
Note 3 For the proper operation of the thermostat, the floor sensor  
must be centered between two heater wires having a  
maximum temperature of 80°C. The floor sensor wire must  
not cross any heater wire or be placed close to it.  
p
Supply: 230 VAC, 50 Hz  
Load: 15 A maximum (resistive only)  
Power: 3450 Watts (NI) @ 230 VAC  
Conformity: EN60730-2-9 / EN50081-1 / EN50082-2  
Storage: -20°C to 50°C  
r Push wires into the electrical box and  
secure the base to the electrical box  
anchorage. The head of the screw  
must be less than 2 mm thick.  
Protection: Class 2  
Protection degree: IP21  
Automatic action: Type 1.B  
Environment: Normally polluted  
Size (H • W • D) : 2.95 x 2.95 x 0.55 in. (75 x 75 x 14 mm)  
s BEFORE installing the control  
module onto the base, set the  
configuration switches (if any)  
on the control module (refer to  
the user guide).  
NOTE: The terminals are designed to handle a cross-section of wire  
measuring 0.33 to 3.1 mm2.  
4
.
Procedure  
q
n Remove the screw holding the  
control module to the power base  
and lift the lower part upwards.  
The screw cannot be completely  
removed.  
WARNING: This power base must be used only with 15-minute  
heating cycles. If your control module has a selector switch for  
choosing the heating cycle, ensure that the switch is correctly set.  
t Return power to the heating system.  
PB130  
400-130-001-E  
19/9/05  
1/1