Home

href="
RLV3100  
User Guide  
Digital Non-programmable Thermostat  
NOTE: All cables and connections must comply with local electrical  
codes. This thermostat has tinned copper wires for line and load  
connections. Special CO/ALR solderless connectors must be used if  
these wires will be connected to aluminium conductors.  
Percentage of  
heating time *  
Temperature  
display  
2-wire Installation  
Temperature adjustment buttons  
The thermostat displays the percentage of heating time required to  
*
maintain the desired temperature. For example, is displayed when  
heating is activated 40 percent of the time.  
1
.
4-wire Installation  
Applications  
n
The RLV3100 thermostat can be used to control an electric heating  
system such as an electric baseboard heater, a radiant ceiling, a  
radiant floor, a convector, etc.  
The thermostat cannot be used with the following:  
a resistive load under 2 A  
a resistive load over 12.5 A  
systems driven by a contactor or a relay (inductive load)  
fan-forced heating systems  
central heating systems  
2
.
Supplied Parts  
One (1) thermostat  
o
Mount the back plate to the electrical  
box using the provided screws. Insert  
the screws through the left or right pair  
of mounting holes of the back plate.  
Two (2) 6-32 mounting screws  
Two (2) solderless connectors  
3
.
Installation Procedure  
TURN OFF POWER OF THE HEATING SYSTEM AT THE MAIN  
p
POWER PANEL TO AVOID ELECTRIC SHOCK.  
Set the switch on the back of the  
front plate to °C or °F to select  
the temperature display format.  
Loosen  
the  
screw  
underneath the thermostat  
and separate the front plate  
from the base plate.  
Re-install the front plate of  
the thermostat on the base  
plate and secure it in place  
with the screw underneath  
the thermostat.  
NOTE: The screw cannot be  
completely removed.  
Connect the thermostat wires to the power and to the load using  
solderless connectors for copper wires. The thermostat wires are not  
polarized; meaning either wire can be connected to the load or to the  
power supply.  
NOTE: If there is a protective film or sticker on the display, peel it off.  
RLV3100  
69-1917EF  
7/24/06  
1/2  
href="
7
.
Apply power to the heating system. Verify the installation by checking  
that the heater can be turned On and Off by raising and lowering the  
Specifications  
- Supply: 240 VAC, 50/60 Hz  
Minimum load: 500 W (2 A resistive only)  
- Maximum load: 3000 W (12.5 A resistive only)  
t
setpoint using the  
buttons.  
-
ATTENTION: Keep the thermostat's air vents clean and free from  
obstructions at all times.  
-
-
-
-
-
-
Display range: 0 to 50°C (32 to 122°F)  
Setpoint range: 5 to 30°C (40 to 85°F)  
Resolution: 0.5°C (1°F)  
4
.
Temperature Display and Setting  
q
The thermostat normally displays the actual (measured) temperature.  
Storage: -20 to 50°C (-4 to 120°F)  
Dimensions: 126 x 121 x 31 mm (5.0 x 4.8 x 1.2 inches)  
Approval: c UL us  
To view the set  
temperature (setpoint),  
press once on either of  
the temperature  
Appears  
8
.
adjustment buttons.  
when the  
setpoint is  
displayed  
Warranty  
;
To change the setpoint,  
press the appropriate  
button until the desired  
value is displayed.  
Honeywell warrants this product, excluding battery, to be free from  
defects in the workmanship or materials, under normal use and  
service, for a period of one (1) year from the date of purchase by the  
consumer. If at any time during the warranty period the product is  
determined to be defective or malfunctions, Honeywell shall repair or  
replace it (at Honeywell's option).  
Heating power  
indicator  
If the product is defective,  
NOTE: The display is backlit for 10 seconds when either button is  
pressed.  
(i) return it, with a bill of sale or other dated proof of purchase, to  
the place from which you purchased it, or  
5
.
(ii) call Honeywell Customer Care at 1-800-468-1502. Customer  
Care will make the determination whether the product should be  
returned to the following address: Honeywell Return Goods,  
Dock 4 MN10-3860, 1885 Douglas Dr N, Golden Valley, MN  
Power Outage  
r
The setpoint is stored in non-volatile memory and is not erased when  
there is a power outage.  
55422, or whether a replacement product can be sent to you.  
This warranty does not cover removal or reinstallation costs. This  
warranty shall not apply if it is shown by Honeywell that the defect or  
malfunction was caused by damage which occurred while the  
product was in the possession of a consumer.  
Honeywell's sole responsibility shall be to repair or replace the  
product within the terms stated above. HONEYWELL SHALL NOT  
BE LIABLE FOR ANY LOSS OR DAMAGE OF ANY KIND,  
INCLUDING ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES  
RESULTING, DIRECTLY OR INDIRECTLY, FROM ANY BREACH  
OF ANY WARRANTY, EXPRESS OR IMPLIED, OR ANY OTHER  
FAILURE OF THIS PRODUCT. Some states do not allow the  
exclusion or limitation of incidental or consequential damages, so this  
limitation may not apply to you.  
6
.
Troubleshooting  
s
PROBLEM  
SOLUTIONS  
This is normal. Under normal operation, the  
thermostat housing can reach a temperature  
between 35 °C (95 °F) and 40 °C (104 °F).  
Thermostat is hot.  
Correct if any the following conditions  
applies:  
The thermostat is exposed to air draft.  
Displayed tempera-  
ture is wrong.  
The sticker on the thermostat’s screen  
has not been removed.  
THIS WARRANTY IS THE ONLY EXPRESS WARRANTY  
HONEYWELL MAKES ON THIS PRODUCT. THE DURATION OF  
ANY IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF  
The thermostat is located near or above  
a heat source such as a light dimmer.  
MERCHANTABILITY AND FITNESS FOR  
A
PARTICULAR  
The thermal protection device on the heater  
was temporarily opened. This can happen if  
the heater is obstructed by furniture or curtain  
and has overheated, or if the heater’s thermal  
protection device is too sensitive.  
Display disap-  
pears and reap-  
pears after a few  
minutes.  
PURPOSE, IS HEREBY LIMITED TO THE ONE-YEAR DURATION  
OF THIS WARRANTY. Some states do not allow limitations on how  
long an implied warranty lasts, so the above limitation may not apply  
to you.  
This warranty gives you specific legal rights, and you may have other  
rights which vary from state to state.  
Display looks faded The heating system is less than the required  
when heating is  
activated.  
minimum load. This thermostat cannot be  
used below that rating.  
If you have any questions concerning this warranty, please write  
Honeywell Customer Relations, 1985 Douglas Dr, Golden Valley, MN  
55422 or call 1-800-468-1502. In Canada, write Retail Products  
ON15-02H, Honeywell Limited/Honeywell Limitée, 35 Dynamic Drive,  
Scarborough, Ontario M1V4Z9.  
9
.
Customer assistance  
If you have any questions about the operation of your thermostat,  
please go to http://yourhome.honeywell.com, or call Honeywell  
Customer Care toll-free at 1-800-468-1502.  
RLV3100  
69-1917EF  
7/24/06  
2/2  
href="
RLV3100  
Guide d’utilisateur  
Thermostat non programmable  
NOTA : Tous les câbles et les raccordements doivent être conformes au  
code d’électricité local. Les fils du thermostat qui servent aux  
raccordements de ligne et de charge sont étamés. Des connecteurs CO/  
ALR spéciaux doivent être utilisés si ces fils doivent être reliés à des  
conducteurs d'aluminium.  
Pourcentage  
d’utilisation du  
chauffage *  
Affichage de la  
température  
Installation à 2 fils  
Boutons de réglage  
de la température  
*
Le thermostat affiche le pourcentage d'utilisation du chauffage  
requis pour maintenir la température désirée. Par exemple,  
s’affiche lorsque le chauffage est activé 40 % du temps.  
Installation à 4 fils  
1
.
Applications  
n
Le thermostat RLV3100 peut servir à commander un appareil de  
chauffage électrique tel qu’une plinthe chauffante, un plafond radiant,  
un plancher chauffant, un convecteur, etc.  
Ce thermostat ne peut pas être utilisé dans les cas suivants :  
si la charge résistive est inférieure à 2 A  
si la charge résistive est supérieure à 12,5 A  
si l’appareil est muni d’un contacteur ou d’un relais (charge  
inductive)  
si l’appareil est muni d’un ventilateur  
si l’appareil est un système de chauffage central  
2
.
Fixer la base sur une boîte électrique à  
l'aide des vis fournies. Passer les vis  
dans l’une des deux paires de trous de  
montage (soit la gauche ou la droite).  
Pièces fournies  
Un (1) thermostat  
o
Deux (2) vis de montage 6-32  
Deux (2) connecteurs sans soudure  
3
.
Installation  
p
Positionner le commutateur à l’arrière  
de la plaque frontale du thermostat en  
°C ou °F pour sélectionner le format  
d’affichage de la température.  
METTRE LE SYSTÈME DE CHAUFFAGE HORS TENSION AFIN  
D’ÉVITER TOUT RISQUE DE CHOC ÉLECTRIQUE.  
Desserrer la vis sous le  
thermostat et séparer la  
Replacer la plaque frontale  
du thermostat sur sa base  
et resserrer la vis sous le  
thermostat.  
plaque du  
frontale  
thermostat de sa base.  
NOTA : La vis ne peut être  
retirée complètement.  
Brancher le thermostat à  
l’alimentation et à la charge  
avec des connecteurs sans  
soudure pour fils de cuivre. Les fils du thermostat ne sont pas  
polarisés. Donc, le sens du branchement n’a aucune importance.  
NOTA : Enlever la pellicule (autocollant) de l’écran s’il y en a une.  
RLV3100  
69-1917EF  
7/24/06  
1/2  
href="
7
.
Mettre le système de chauffage sous tension. Vérifier l’installation en  
s’assurant que le système de chauffage puisse être activé et  
désactivé en augmentant et en diminuant la température de consigne  
Fiche technique  
- Alimentation : 240 V c.a., 50/60 Hz  
t
à l’aide des boutons  
.
- Charge minimale : 500 W (2 A résistive uniquement)  
MISE EN GARDE : Garder les ouvertures d’aération du thermostat  
- Charge maximale : 3000 W (12,5 A résistive uniquement)  
propres et non obstruées  
-
Plage d’affichage : 0 °C à 50 °C (32 °F à 122 °F)  
4
.
- Plage de réglage : 5 °C à 30 °C (40 °F à 85 °F)  
- Resolution: 0.5°C (1°F)  
Affichage et réglage de la température  
q
-
-
Entreposage : -20 °C à 50 °C (-4 °F à 120 °F)  
Le thermostat affiche normalement la température réelle (mesurée).  
Dimensions: 126 x 121 x 31 mm (5,0 x 4,8 x 1,2 pouces)  
Pour afficher la  
température de  
consigne (réglée),  
appuyer une fois sur  
l’un des boutons de  
réglage de la  
- Homologation : c UL us  
Apparaît  
8
.
lorsque la  
consigne  
est affichée  
Garantie  
;
Honeywell garantit ce produit, à l'exception des piles, contre tout vice de  
fabrication ou de matière dans la mesure où il en est fait une utilisation et  
un entretien convenables, et ce, pour un (1) an à partir de la date d'achat  
par le consommateur. En cas de défectuosité ou de mauvais  
fonctionnement pendant la période de garantie, Honeywell remplacera  
ou réparera le produit (au gré de Honeywell).  
température.  
Pour modifier la  
température, appuyer  
sur le bouton approprié  
jusqu’à ce que la valeur  
désirée apparaisse.  
Indicateur de puissance  
de chauffage  
Si le produit est défectueux,  
(
i) le retourner, accompagné d'une preuve d'achat indiquant la date  
d'achat, à l’endroit où il a été acheté, ou  
(
ii) s'adresser au Service à la clientèle de Honeywell en composant le  
NOTA : L’écran est rétroéclairé pendant 10 secondes lorsqu’on  
appuie sur n’importe quel bouton.  
1
-800-468-1502. Le Service à la clientèle déterminera alors si le  
produit doit être retourné à l'adresse suivante : Honeywell Return  
Goods, Dock 4 MN10-3860, 1885 Douglas Dr N, Golden Valley, MN  
5
.
5
5422, ou si un produit de remplacement peut vous être expédié.  
Panne de courant  
La température de consigne est sauvegardée dans une mémoire non  
r
La présente garantie ne couvre pas les frais de retrait ou de  
réinstallation. La présente garantie ne s'appliquera pas s'il est démontré  
que la défectuosité ou le mauvais fonctionnement est dû à un  
endommagement du produit alors que le consommateur l'avait en sa  
possession.  
volatile et n’est donc pas effacée durant une panne de courant.  
6
.
Problèmes et solutions  
La responsabilité de Honeywell se limite à réparer ou à remplacer le  
produit conformément aux modalités susmentionnées. HONEYWELL  
N'EST EN AUCUN CAS RESPONSABLE DES PERTES OU  
s
PROBLÈMES  
SOLUTIONS  
DOMMAGES,  
Y COMPRIS LES DOMMAGES INDIRECTS OU  
Ceci est normal. En fonctionnement nor-  
mal, le boîtier du thermostat peut attein-  
dre une température entre 35 °C (95 °F)  
et 40 °C (104 °F).  
ACCESSOIRES DÉCOULANT DIRECTEMENT OU INDIRECTEMENT  
D'UNE VIOLATION QUELCONQUE D'UNE GARANTIE, EXPRESSE  
OU TACITE, APPLICABLE AU PRÉSENT PRODUIT NI DE TOUTE  
AUTRE DÉFECTUOSITÉ DU PRÉSENT PRODUIT. Certaines provinces  
ne permettent pas l'exclusion ou la restriction des dommages indirects et,  
par conséquent, la présente restriction peut ne pas s'appliquer.  
Le thermostat est  
chaud.  
Corriger si l’une des conditions suivan-  
tes existe :  
LA PRÉSENTE GARANTIE TIENT LIEU DE TOUTES LES AUTRES  
GARANTIES, EXPRESSES OU TACITES, ET LES GARANTIES DE  
Il y a un courant d’air à proximité.  
La température affichée  
est erronée.  
L’autocollant sur l’écran du ther-  
mostat n’a pas été enlevé.  
VALEUR MARCHANDE ET DE CONFORMITÉ  
À
UNE FIN  
PARTICULIÈRE SONT PAR LES PRÉSENTES EXCLUES APRÈS LA  
PÉRIODE D’UN AN DE LA PRÉSENTE GARANTIE. Certaines  
provinces ne permettent pas de limiter la durée des garanties tacites et,  
par conséquent, la présente limitation peut ne pas s'appliquer.  
La présente garantie donne au consommateur des droits légaux  
spécifiques et peut-être certains autres droits qui peuvent varier d'une  
province à l'autre.  
Pour toute question concernant la présente garantie, prière d'écrire au  
Service à la clientèle de Honeywell à l'adresse suivante : Honeywell  
Customer Relations, 1985 Douglas Drive, Golden Valley, MN 55422, ou  
encore composer le 1-800-468-1502. Au Canada, prière de s'adresser  
au service des Produits de détail, Honeywell Limited/Honeywell Limitée,  
35, Dynamic Drive, Scarborough (Ontario) M1V 4Z9.  
Le thermostat est situé près ou  
au-dessus d’une source de chaleur  
tel qu’un gradateur de lumière.  
La protection thermique de la plinthe  
était temporairement ouverte. Ceci peut  
se produire suite à une surchauffe lors-  
que la plinthe est obstruée par un meu-  
ble ou un rideau, ou si la protection  
thermique de la plinthe est trop sensible.  
L’affichage disparaît et  
ne réapparaît qu’après  
quelques minutes.  
Le système de chauffage est inférieur à  
la charge minimale requise. Dans le cas  
échéant, ce thermostat ne peut pas être  
utilisé.  
L’affichage est pâle lors-  
que le chauffage est  
activé.  
9.  
Service à la clientèle  
Si vous avez des questions sur le fonctionnement de votre  
thermostat, veuillez consulter http://yourhome.honeywell.com, ou  
vous adresser au Service à la clientèle de Honeywell en composant  
sans frais le 1-800-468-1502  
.
RLV3100  
69-1917EF  
7/24/06  
2/2