Honeywell RTH6350D1000E1 Thermostat User Manual

Home

System

Installation

Guide

RedLINK™Wireless System

With Equipment Interface Module

Français : voir la page 21 • Español: vea la página 41

Wireless control for up to 3 Heat/2 Cool heat pump systems or up to 2 Heat/2

Cool conventional systems.

Installation guide for:

•

Wireless equipment interface module

FocusPRO wireless thermostats

Wireless remote control

Wireless outdoor air sensor

Return air sensor

DISCONNECT POWER BEFORE BEGINNING INSTALLATION. Can cause

electrical shock or equipment damage.

MERCURY NOTICE: If this product is replacing a control that contains mercury in

a sealed tube, do not place the old control in the trash. Contact your local waste

management authority for instructions regarding recycling and proper disposal.

Must be installed by a trained, experienced technician. Read these

instructions carefully. Failure to follow these instructions can damage the product or

cause a hazardous condition.

U.S. Registered Trademark.

9-2091EFS-07

RedLINK Installation Guide (EIM)

System installation at a glance

The THM5320R equipment interface module (EIM) provides control of all heating

and cooling equipment from any FocusPRO wireless thermostat.

Thermostat

Optional outdoor

air sensor

HVAC equipment

Remote

control

EIM

M28484

Installation procedure

Mount and wire EIM.................................................................. Pages 3-4

Install batteries in wireless devices ...............................................Page 5

Link all devices to wireless network........................................ Pages 5-7

Exit wireless setup ..........................................................................Page 8

Customize thermostat (installer setup).................................. Pages 8-12

Mount thermostat and outdoor sensor .......................................Page 13

To replace system components if needed, see page 15

For system-specific wiring guides, see pages 16-17

If you have more than one Equipment Interface Module (EIM): Thermostats

are linked to specific EIMs. Optional accessories must be linked to each EIM

separately.

DISCONNECT POWER BEFORE BEGINNING INSTALLATION. Can cause electrical

shock or equipment damage.

9-2091EFS—07

Français : voir la page 21 • Español: vea la página 41

Mount and wire EIM

Mount EIM on wall near HVAC equipment, or on the equipment itself.

Do not install inside HVAC equipment. Use screws & anchors as appropriate

for mounting surface.

Install return air sensor (optional)**

The return air sensor maintains safe

Install EIM

indoor temperature (62° F in Heat, 82° F

in Cool) if thermostat power is lost.

THM5320R

POWER

HEAT

COOL

FAN

Drill 1/4” hole

WIRELESS

SETUP

CONNECTED

(6.4mm)

Install sensor on return air duct at least

2” (305mm) upstream from ventilator,

CONNECT

EDEVICE

M28468

FLASHING:CONN

GREEN:CONNECT

ECTINGTOREMOT

RED:REMOTEDE VE DTOREMOTEDEVICE(S)

ICE(S)NOTCOMM

UNICATING

humidifier or dehumidifier (do not mount

downstream)

* For hydronic applications, use

M28467 C7189U1005 Remote Indoor Sensor and

mount in the living space.

EIM wiring

Strip 1/4” insulation, then insert wires

as shown.

M28494

Press tabs only to remove wires from

terminal block if necessary.

Wiring must comply with local

electrical codes.

M28469

Continued on next page >>

69-2091EFS—07

RedLINK Installation Guide (EIM)

EIM wiring guide

FURNACE

See detailed wiring guides for specific system

Transformer

types on pages 16-17.

4Vac

120Vac

CONVENTIONAL SYSTEMS

Stage 1 heat

Stage 2 heat

Fan

EQUIPMENT INTERFACE MODULE

Jumper

Air Conditioning

Compressor

(

Stage 1)

A/B/C/D UNUSED

Compressor

Stage 2)

(

reserved for future use)

(

Return air sensor**

* or C7189U1005 Remote indoor sensor for hydronic

M28470

AIR HANDLER

HEAT PUMP SYSTEMS

Transformer

4Vac

120Vac

EQUIPMENT INTERFACE MODULE

Jumper

Changeover

relay

Backup heat

(

gas/electric)

Compressor

Stage 1)

(

Compressor

Stage 2)

(

A/B/C/D UNUSED

Fan Relay

Relay **

(

reserved for future use)

Return

Air Sensor

* L terminal sends continuous output when thermostat is

set to EmHeat. L terminal is for use with zone panels.

M28471

9-2091EFS—07

Français : voir la page 21 • Español: vea la página 41

Install batteries in wireless devices

When system wiring is complete, install batteries in all devices. Make sure

batteries are inserted properly (see polarity marks on illustrations below).

Thermostat

Programmable models only

M28472

M28474

Install 2 fresh AA

batteries

M28473

Install quick reference

card

Remote control (optional)

Outdoor air sensor (optional)

Install 2 fresh AA

Install 3 fresh AA

batteries

lithium batteries

M28475

M28476

Link all devices to wireless network

Press and release CONNECT

Restore AC power, then press and release

the CONNECT button at the EIM. Wait for

green flashing light to begin linking devic-

es to the wireless network (see pages 6-7).

If the light stops flashing before you have

linked all devices, press CONNECT again.

If light does not flash, another EIM/

wireless adapter may be in wireless setup

mode. Exit wireless setup at the other

EIM/wireless adapter.

M28495

Flashing status light times out after 15

minutes of inactivity. Press CONNECT

again if necessary.

Continued on next page >>

69-2091EFS—07

RedLINK Installation Guide (EIM)

Link thermostat to wireless network

Zone number

Wireless Setup

Press NEXT (always leave zone number set

to zero).

Zone numbers 1-4 are for use with

TrueZONE panels only.

M28477

Zone name

Wireless Setup

Press NEXT (or see page 11 to change the

zone name if needed).

Change zone name only if you have more

than one thermostat and EIM.

Back

M28478

Wireless Setup

Press CONNECT to establish a link to the wire-

less network.

If E1 appears, see error codes on page 14.

Back

Connect

M28479

Wireless Setup

Connected

After a brief pause, the confirmation screen

at left should be displayed, to verify that the

wireless connection has been established.

Press DONE to display the home screen.

Done

M28480

9-2091EFS—07

Français : voir la page 21 • Español: vea la página 41

Link remote control to wireless network (optional)

Make sure the Connected light on the

EIM is flashing (see page 5).

Press CONNECT at the remote. There will

be a short delay as the remote seeks a

signal from the wireless network.

CONNECT

When the screen displays "Connected,"

press DONE.

WIRELESS SETUP

Press NO at the next screen to save and

exit. (Or press YES and repeat steps 1-4

to link another EIM.)

M28481

Press to link

Press to save

another EIM

and exit

If E1 appears, see error codes on page 14.

The linking procedure may time out if there is

no keypress within 30 minutes. To begin again,

press and hold the blank space (or arrow, if

present) in the lower right corner of the screen

until the display changes (about 3 seconds).

YES

CONNECT MORE?

M28482

Link outdoor sensor to wireless network (optional)

Press and release

1 Make sure the Connected light on the

EIM is flashing (see page 5).

Press and release the CONNECT button

on the back of the sensor.

Check thermostat to verify that the

outdoor sensor is working. After about

5 seconds, the thermostat should

display outdoor temperature and

humidity.

(

If you are installing more than one EIM,

repeat steps 1-3 for each.)

M28483

69-2091EFS—07

RedLINK Installation Guide (EIM)

Exit wireless setup

Press CONNECT at the EIM to exit wireless setup (light should stop flashing).

Note: The EIM will automatically exit wireless setup after 15 minutes of inactivity.

Note: If installing more than one thermostat and EIM, you must exit wireless setup

before installing an additional thermostat and EIM.

Customize thermostat (installer setup)

Follow the steps below to begin installer setup. At each function screen, press

s or t to change the setting as desired, then press NEXT to advance to the

next function screen.

See tables on pages 9-11 for a description of options for each function.

FAN

Done

Back

M28486

M28485

To begin, press and hold the FAN and s buttons

until the display changes (about 3 seconds).

Function

Setting

Press s or t to change

setting (see tables on pages

-11).

Done

Back

M28487

Press NEXT to display next

function screen.

Press DONE to save & exit.

9-2091EFS—07

Français : voir la page 21 • Español: vea la página 41

Installer setup tables

Setup function

Settings & options (factory default in bold)

Zone number

No zoning (single thermostat used with THM5320R EIM)

[

Options: select zone 1, 2, 3 or 4]

System type

1 heat/1 cool conventional

1 heat/1 cool heat pump (no aux. heat)

Heat only (includes Series 20)

Heat only with fan

Cool only

2 heat/1 cool heat pump

2 heat/2 cool conventional

2 heat/1 cool conventional

1 heat/2 cool conventional

2 heat/2 cool heat pump

3 heat/2 cool heat pump

Changeover valve

O/B terminal controls valve in cooling

O/B terminal controls valve in heating

(

O/B terminal)

Fan control

Gas/Oil heat (equipment controls fan)

Electric furnace (thermostat controls fan)

(

conventional heat)

Backup heat (Aux &

EmHeat)

Electric backup heat

Fossil fuel backup heat

Stage 1 heat cycle

rate (CPH: cycles/

hour)

Gas or oil furnaces (less than 90% efficiency)

Steam or gravity systems

Hot water systems & furnaces of over 90% efficiency

Electric furnaces

[

Cycle rate options: 1 to 12 CPH]

Stage 2 heat cycle

rate (CPH)

Gas or oil furnaces (less than 90% efficiency)

Steam or gravity systems

Hot water systems & furnaces of over 90% efficiency

Electric furnaces

[

Cycle rate options: 1 to 12 CPH]

Stage 3 heat cycle

rate (CPH)

Gas or oil furnaces (less than 90% efficiency)

Steam or gravity systems

Hot water systems & furnaces of over 90% efficiency

Electric furnaces

[

Cycle rate options: 1 to 12 CPH]

Emergency heat cycle9

rate (CPH)

Electric furnace

[Cycle rate options: 1 to 12 CPH]

Stage 1 compressor

cycle rate

Recommended cycle rate

[Cycle rate options: 1 to 6 CPH]

Stage 2 compressor

cycle rate

Recommended cycle rate

[Cycle rate options: 1 to 6 CPH]

Heat pump type

Air to Air Heat Pump

Geothermal heat pump

Manual/Auto

changeover

Manual (User options: Heat/Cool/Off)

Automatic (User options: Heat/Cool/Auto/Off)

Adaptive Intelligent Applies only to Model TH6320

Recovery™

Off

Temperature

display

Fahrenheit

Celsius

69-2091EFS—07

RedLINK Installation Guide (EIM)

Installer setup tables

Setup function

Settings & options (factory default in bold)

Compressor off time

minimum)

5 minutes (Heat On/Cool On flashes during off time)

[Options: 0 to 4 minutes]

(

Schedule format

Applies only to Model TH6320

Weekday/weekend program schedule

Weekday/Saturday/Sunday program schedule

External fossil fuel kit 1

External fossil fuel kit controls backup heat

Thermostat controls backup heat (outdoor sensor required)

Dual fuel heat pump

control

Droop control**

No droop control**

Droop control with Aux Heat Lockout**

Droop temperature

Auto temperature droop 2° F (1° C)

[Options: 2 to 5 (2 to 5° F / 1 to 2.5° C)]

(

dual fuel)

Dual fuel upstage to

furnace timer

1 hour**

[Options: 0 (off) to 16 hours]

Outdoor air sensor?

Yes

Heat pump

compressor lockout

No heat pump compressor lockout**

5° F (-15° C)

10° F (-12° C)

15° F (-9.5° C)

20° F (-6.5° C)

25° F (-4° C)

30° F (-1° C)

35° F (1.5° C)

40° F (4.5° C)

45° F (7° C)

(

balance point)

10 50° F (10° C)

11 55° F (13° C)

12 60° F (15.5° C)

Heat pump

auxiliary lockout

No heat pump auxiliary lockout**

5° F (-15° C)

10° F (-12° C)

15° F (-9.5° C)

20° F (-6.5° C)

25° F (-4° C)

30° F (-1° C)

35° F (1.5° C)

40° F (4.5° C)

45° F (7° C)

10 50° F (10° C)

11 55° F (13° C)

12 60° F (15.5° C)

13 65° F (18.5° C)

Auxiliary heat control Applies only to Model TH5320

Comfort**

Economy

Maximum heat

setpoint

90 Max. heat temperature setting is 90° F (32° C)

[Options: 40 °F to 90 °F (4.5 °C to 32 °C)]

Minimum cool

setpoint

50 Min. cool temperature setting is 50° F (10° C)

[Options: 50 °F to 99 °F (10 °C to 37 °C)]

Temp. display offset

Thermostat displays actual temperature

[Options: -3 to +3 °F offset (-1.5 to +1.5 °C)]

(

indoor)

Temp. display offset

Thermostat displays actual temperature

[Options: -5 to +5 °F offset (-2.5 to +2.5 °C)]

(

outdoor)

Humidity display

offset (outdoor)

Thermostat displays actual humidity

[Other options: 0 = -15%, 1 = -10%, 2 = -5%, 4 = +5%, 5 = +10%,

= +15% offset]

* See page 11

9-2091EFS—07

Français : voir la page 21 • Español: vea la página 41

Installer setup tables

Setup function

Settings & options (factory default in bold)

Zone name

52 Thermostat