Home

href="
1E30(W)/1F30(W)  
Non-Anticipated  
WHITE-RODGERS  
Millivolt Room Thermostat  
INSTALLATION INSTRUCTIONS  
Operator: Save these instructions for future use!  
FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY  
BEFORE INSTALLING OR OPERATING THIS CONTROL COULD CAUSE  
PERSONAL INJURY AND/OR PROPERTY DAMAGE.  
DESCRIPTION  
These low voltage thermostats are specially designed for  
use on self-generating systems. They are non-antici-  
pated, enabling them to be used on self-generated sys-  
tems having pilot generator outputs from 250 to 750  
millivolts.  
1F30  
1E30  
PRECAUTIONS  
This control is a precision instrument, and should be  
handled carefully. Rough handling or distorting compo-  
nents could cause the control to malfunction.  
Ifindoubtaboutwhetheryourwiringismillivolt,line,orlow  
voltage, have it inspected by a qualified heating and air  
conditioning contractor, electrician, or someone familiar  
with basic electricity and wiring.  
CAUTION  
!
Do not exceed the specification ratings.  
All wiring must conform to local and national electrical  
codes and ordinances.  
To prevent electrical shock and/or equipment  
damage, disconnect electric power to system, at  
main fuse or circuit breaker box, until installation  
is complete.  
CONTENTS  
Donotshortoutterminalsongasvalveorprimary  
control to test. Short or incorrect wiring will burn  
out heat anticipator and could cause personal  
injury and/or property damage.  
Description .......................................................... 1  
Precautions ......................................................... 1  
Specifications...................................................... 2  
Installation........................................................... 2  
Select Thermostat Location  
WARNING  
!
Route Wires to Location  
Attach Thermostat to Wall  
Do not use on circuits exceeding 750 millivolts.  
Higher voltage will damage control and could  
cause shock or fire hazard.  
Operation & Maintenance ................................... 3  
Calibrating Thermometer  
Calibrating Thermostat  
ATTENTION!  
This product contains mercury. There will not be any exposure to mercury under normal conditions of use. This product may replace a unit  
which contains mercury. Do not open mercury cells. If a cell becomes damaged, do not touch any spilled mercury. Wearing non-absorbent  
gloves, take up the spilled mercury with sand or other absorbent material and place into a container which can be sealed. If a cell becomes  
damaged, the unit should be discarded. Mercury must not be discarded in household trash. When this unit or the unit it is replacing is to be  
discarded, place in a suitable container and return to us at WHITE-RODGERS.  
PART NO. 37-5583A  
WHITE-RODGERS DIVISION  
EMERSON ELECTRIC CO.  
9797 REAVIS RD., ST. LOUIS, MO. 63123  
(314) 577-1300, Fax (314) 577-1517  
Replaces 37-9587C  
9531  
Printed in U.S.A.  
9999 HWY. 48, MARKHAM, ONT. L3P 3J3  
(905) 475-4653, FAX (905) 475-4625  
R
href="
SPECIFICATIONS  
THERMAL DATA:  
ELECTRICAL DATA  
Temperature Range: 10° to 32°C (50° to 90°F)  
Switch Rating: 250 to 750 millivolt DC 0.1 Amps  
Differential:  
1.7°C (3°F)  
Switch Action: SPST - Sealed mercury switch  
INSTALLATION  
SELECT THERMOSTAT LOCATION  
ROUTE WIRES TO LOCATION  
Proper location insures that the thermostat will provide a  
comfortable home temperature. Observe the following  
general rules when selecting a location:  
1. If an old thermostat is being replaced and is in a  
satisfactory location, and the wiring appears to be in  
good condition, use existing wiring. If in doubt, rewire.  
1. Locate thermostat about 5 ft. above the floor.  
2. Ifanewlocationischosenorifthisisanewinstallation,  
thermostat wire must first be run to the location se-  
lected. All wiring must conform with local and national  
electrical codes and ordinances.  
2. Install thermostat on a partitioning wall, not on an  
outside wall.  
3. Never expose thermostat to direct light from lamps,  
sun, fireplaces or any temperature radiating equip-  
ment.  
NOTE  
4. Avoid locations close to windows, adjoining outside Because of the small amount of power available on self-  
walls, or doors that lead outside.  
generating systems, the gas valve may not operate if  
there is too much resistance in the circuit. Therefore,  
choose a location that does not require any more wire  
thantherecommendedlengthsshownintheThermostat  
Wire Length Table.  
5. Avoid locations close to air registers or in the direct  
path of air from them.  
6. Make sure there are no pipes or duct work in that part  
of the wall chosen for the thermostat location.  
THERMOSTAT WIRE LENGTH TABLE  
7. Never locate thermostat in a room that is warmer or  
cooler than the rest of the home, such as the kitchen.  
Solid  
Max. Length Max. Combined Length  
Wire Sizes (2-wire cable)  
(2 single wires)  
60 ft.  
8. Avoid locations with poor air circulation, such as be-  
hind doors or in alcoves.  
No. 18  
No. 16  
No. 14  
30 ft.  
50 ft.  
80 ft.  
9. The living or dining room is normally a good location,  
provided there is no cooking range or refrigerator on  
opposite side of wall.  
100 ft.  
160 ft.  
1
3. Probe for obstructions in partition before drilling ⁄ ”  
2
hole in wall at selected location. Take up quarter round  
and drill a small guide hole for sighting (see Fig. 1).  
From basement, drill 3⁄  
4
” hole in partition floor next to  
1/2" HOLE FOR  
THERMOSTAT WIRE  
guide hole. In houses without basements, drill 1⁄  
2
” hole  
through ceiling and into partition from above (see Fig.  
1).  
STOUT CORD WITH 6"  
CHAIN ATTACHED  
4. Through this hole drop a light chain, or 6” chain  
attached to a strong cord. Snag cord in basement with  
hooked wire. In houses without basements, drop cord  
through hole in ceiling and down partitioning; snag  
cord at the thermostat location.  
APPROXIMATELY  
BASEBOARD  
STRIP MOLDING  
5 FEET  
1/4" GUIDE HOLE  
FOR SIGHTING  
QUARTER ROUND  
REMOVED  
5. Attach thermostat wire to cord and pull wire through  
hole in wall so that 6” of wire protrudes.  
3/4" HOLE IN FLOOR OF PARTITION  
HOOKED WIRE FOR SNAGGING CHAIN  
Figure 1. Routing Thermostat Wires  
2
href="
5. Position thermostat base over hole in wall and mark  
mounting hole location on wall.  
CAUTION  
!
To prevent electrical shock and/or equipment  
damage, disconnect electric power to system, at  
main fuse or circuit breaker box, until installation  
is complete.  
6. Drill mounting hole.  
7. Fasten base loosely to wall using mounting screws.  
Place a level against the top of the thermostat base,  
adjust until level, and tighten mounting screws to  
secure base. If holes in wall are too large and do not  
allowyoutotightenthemountingscrewssecurely, use  
plastic expansion plugs.  
NOTE  
Thistypicalwiringdiagramshowsonlyterminalidentifica-  
tionandwiringhook-up. Alwaysrefertothewiringinstruc-  
tions provided by the equipment manufacturer for system  
hook-up.  
8. Snap cover on the thermostat base and set tempera-  
ture lever to desired setpoint.  
9. Turn on electrical power to system.  
All wiring should be installed according to local and  
national electrical codes and ordinances.  
Thermostat  
Switch  
ATTACHING THERMOSTAT  
1. Remove cover from thermostat by gripping the base in  
one hand. Use the other hand to pull gently at the top  
or bottom of the cover.  
Terminal  
Screws  
Heat  
THERMOSTAT  
SYSTEM  
Power Generator  
2. Carefully remove the shipping protective packing from  
the switch.  
Pilot Flame  
Heating  
System  
3. Pull wires through the opening in the thermostat base  
and connect wires beneath the terminal screws (see  
Fig. 2 & 3).  
4. Push excess wiring back into wall and plug hole with  
fire resistant material (such as fiberglass insulation) to  
prevent drafts from affecting thermostat operation.  
Figure 2. Typical Wiring Diagram  
Terminal  
Screws  
COVER  
THERMOSTAT  
BASE  
THERMOSTAT  
BASE  
Figure 3. Parts of Thermostat  
Mounting screws  
COVER  
OPERATION & MAINTENANCE  
CALIBRATING THERMOMETER ON  
THERMOSTAT COVER  
If thermometer reading on cover does not match the  
thermostat:  
Thermometer  
Adjustment  
1. Remove thermostat cover.  
2. Set cover on table near an accurate thermometer.  
3. Allow at least 10 minutes for thermometer to sense  
room temperature.  
4. If the thermometer readings are the same, replace  
thermostat cover.  
5. Ifthethermometerreadingsaredifferent,insertasmall  
screwdriver blade into the thermometer shaft in the  
back of the cover. Adjust until the cover thermometer  
matches the other thermometer (See Fig. 4).  
Back Side of  
Thermostat Cover  
Figure 4. Calibrating Thermostat Thermometer  
6. Replace thermostat cover.  
3
href="
7
6. Slip standard 32” wrench onto hex nut and holding  
CALIBRATING THERMOSTAT  
temperature adjustment lever stationary, turn hex nut  
counter-clockwiseuntilmercuryjustbarelyshiftstoleft  
end of tube (see Fig.5).  
This thermostat has been carefully adjusted at the factory  
and should not require recalibration.  
Duetoenvironmentalconditions,duringnormaloperation  
there may be a few degrees difference between the  
indicator setting of the thermostat and actual room tem-  
perature. If the disagreement is appreciable, however,  
first make sure that the thermostat is properly located and  
leveled. Then, if recalibration still seems necessary, pro-  
7. Replace cover and set thermostat to desired tempera-  
ture. Turn on electrical power to system.  
ceed as follows:  
CAUTION  
!
To prevent electrical shock and/or equipment  
damage, disconnect electric power to system  
until recalibration is complete.  
7/32" Calibration  
Bimetal  
Wrench  
1. Move temperature adjustment lever to a setting about  
5° above room temperature.  
2. Remove thermostat cover. Slip standard 732” wrench  
onto hex nut beneath bimetal, and holding tempera-  
ture adjustment lever stationary, turn hex nut clock-  
wise until mercury shifts to right end of bulb (see Fig.  
5).  
Temperature  
Adjustment  
Lever  
3. Move temperature adjustment lever to lowest setting.  
4. Replacethermostatcover. Wait10minutesforbimetal  
temperature to stabilize. Don’t stand near thermostat  
during this period as your breath and body heat will  
affect temperature of bimetal.  
Figure 5. Calibrating Thermostat  
5. Move temperature adjustment lever to correspond to  
actual temperature. Then remove thermostat cover.  
href="
1E30(W) / 1F30(W)  
Thermostat d’ambiance à millivolts  
sans anticipation  
INSTRUCTIONS D’INSTALLATION  
WHITE-RODGERS  
Utilisateur : conservez ces instructions pour vous y référer au besoin !  
SI VOUS NE LISEZ PAS ATTENTIVEMENT CES INSTRUCTIONS AVANT  
D’INSTALLER ET D’UTILISER LA COMMANDE, VOUS RISQUEZ DE CAUSER  
DES BLESSURES ET DES DOMMAGES MATÉRIELS.  
DESCRIPTION  
Ces thermostats à basse tension ont été conçus spécialement  
pour servir avec des systèmes à génératrice intégrée. Ils ne  
sontpasdotésd’anticipateurs, cequipermetdelesutiliseravec  
des systèmes dont la tension de sortie de la génératrice de  
veilleuse est située entre 250 et 750 millivolts.  
1F30  
1E30  
PRÉCAUTIONS  
Si vous n’êtes pas certain de la tension du câblage de votre Cette commande est un instrument de précision qui doit être  
système (soit en millivolts, à basse tension ou à la tension du manipulé avec soin. Elle peut se détraquer si elle est manipulée  
réseau), faites inspecter le câblage par un électricien, un entre- de façon négligente ou si des composantes sont déformées.  
preneur agréé en chauffage et climatisation ou une personne  
qui a des connaissances de base en électricité et en câblage.  
ATTENTION  
Ne dépassez pas les charges nominales.  
Afindeprévenirleschocsélectriquesetlesdommages  
matériels, coupezl’alimentationélectriqueaupanneau  
dedistributionélectriqueprincipalpendantl’installation.  
Tout le câblage doit être conforme aux codes et règlements  
locaux et nationaux qui régissent les installations électriques.  
Ne court-circuitez pas les bornes du robinet de gaz ou  
de la commande principale lors des essais. Tout court-  
circuit ou câblage inadéquat grillera l’anticipateur de  
chauffage et risque d’entraîner des blessures et des  
dommages matériels.  
TABLE DES MATIÈRES  
Description.....................................................................1  
Précautions ...................................................................1  
Spécifications ................................................................ 2  
Installation .....................................................................2  
Choix d’un site pour le thermostat  
Acheminement du câblage au site  
Installation du thermostat  
Mode d’emploi et entretien ............................................ 3  
Étalonnage du thermomètre du couvercle  
Étalonnage du thermostat  
AVERTISSEMENT  
N’installez pas cet appareil sur des circuits qui dépas-  
sent 750 millivolts. Une tension trop élevée peut  
endommager la commande et poser des risques de  
chocs électriques et d’incendie.  
ATTENTION !  
Cet appareil contient du mercure. Il ne comporte aucun risque d’exposition lorsqu’il est utilisé normalement. L’appareil qu’il remplace peut,  
lui aussi, contenir du mercure. N’ouvrez pas les cellules de mercure. Si une cellule est endommagée, ne touchez pas au mercure qui s’en  
échappe. Enfilez des gants étanches et nettoyez le mercure avec du sable ou une autre substance absorbante, puis placez le matériel  
contaminé dans un contenant qui peut être fermé hermétiquement. Si une cellule est endommagée, l’appareil en entier doit être jeté. Ne pas  
jeter de mercure avec les ordures ménagères. Si vous devez jeter cet appareil ou celui qu’il remplace, placez-le dans un contenant  
convenable et faites-le parvenir à WHITE-RODGERS.  
PIÈCE NO 37-5583A  
Remplace 37-9587C  
DIVISION WHITE-RODGERS CONTROLS  
EMERSON ELECTRIC CO.  
9797 REAVIS RD., ST. LOUIS, MO. 63123  
(314) 577-1300, Télécopieur (314) 577-1517  
Imprimé aux É.-U.A.  
9531  
9999 HWY. 48, MARKHAM, ONT. L3P 3J3  
(905) 475-4653, Télécopieur (905) 475-4625  
R
href="
SPÉCIFICATIONS  
FICHE ÉLECTRIQUE  
FICHE THERMIQUE  
Charges du commutateur :  
Plage des points de consigne : 10°C à 32°C (50°F à 90°F).  
250 à 750 millivolts c.c., 0,1 ampère.  
Différentiel : 1,7°C (3°F).  
Commutateur : Unipolaire unidirectionnel (SPST)  
à bulle de mercure scellé.  
INSTALLATION  
CHOIX D’UN SITE POUR  
LE THERMOSTAT  
Pourquelethermostatpuisseassurerunetempératureambiante  
confortable, il doit être installé dans un site adéquat. Choisissez  
le site en tenant compte des recommandations suivantes :  
ACHEMINEMENT DU CÂBLAGE AU SITE  
1. Si vous remplacez un thermostat dont l’emplacement est  
adéquat et si le câblage semble être en bon état, servez-  
vous du câblage déjà en place. En cas d’incertitude, câblez  
à neuf.  
2. Si vous choisissez un nouvel emplacement ou encore si  
vousinstallezàneuf,vousdevrezcommencerparacheminer  
le câblage au site choisi. Tout le câblage doit être conforme  
aux codes et règlements locaux et nationaux qui régissent  
les installations électriques.  
1. Placez le thermostat environ à 1,5 m (5 pieds) du sol.  
2. Installez le thermostat sur une cloison intérieure et non sur  
un mur extérieur.  
3. N’exposez pas le thermostat directement à la lumière de  
lampes, aux rayons du soleil, ni à la chaleur d’un foyer ou  
d’un radiateur.  
4. Évitez les endroits près d’une fenêtre ou encore d’un mur ou  
d’une porte extérieurs.  
5. Évitez les endroits qui sont près des bouches d’air ou dans  
la trajectoire de l’air qui en émane.  
6. Assurez-vous qu’il n’y a pas de tuyaux ni de conduites dans  
le mur à proximité du site du thermostat.  
NOTE  
La puissance disponible aux systèmes à génératrice intégrée  
étant faible, il est possible que le robinet de gaz ne fonctionne  
pas s’il y a trop de résistance dans le circuit. Par conséquent,  
prenez soin de ne pas choisir un emplacement qui nécessite  
une longueur de fils supérieure à celle recommandée dans le  
tableau de Longueur des fils du thermostat.  
7. N’installez jamais le thermostat dans une pièce qui est  
habituellement plus chaude ou plus froide que le reste du  
domicile, comme la cuisine, par exemple.  
8. Évitez les endroits où la circulation d’air se fait mal, comme  
les alcôves et l’arrière des portes.  
9. La salle à dîner et le salon sont généralement des endroits  
propices s’il n’y a pas de cuisinière ou de réfrigérateur  
adossé au mur derrière le thermostat.  
LONGUEUR DES FILS DU THERMOSTAT  
Calibre des  
Longueur maxi  
Longueur combinée  
maxi (2 fils uniques)  
fils à un brin (fil à 2 conduct.)  
No 18  
No 16  
No 14  
30 pi.  
50 pi.  
80 pi.  
60 pi.  
100 pi.  
160 pi.  
3. Assurez-vousqu’ilnyapasd’obstacledanslemuravantd’y  
1
percer un trou de ⁄  
2
” à l’endroit choisi. Enlevez ensuite le  
quart-de-rond et percez un petit trou de guidage (figure 1).  
Au sous-sol, percez un trou de ⁄  
3
4” dans le plancher de la  
cloison, à côté du trou de guidage. Dans les bâtiments sans  
1
sous-sol, percez le trou de ⁄  
parois de la cloison (figure 1).  
2” dans le plafond, entre les  
4. Passez par le trou que vous avez percé dans le mur une  
chaînette ou une corde solide avec une chaînette de 6”  
attachéeaubout. Accrochezlachaînetteausous-solàl’aide  
d’un crochet de fil de fer. Dans les maisons sans sous-sol,  
passez la chaînette par le trou percé dans le plafond et  
accrochez-le par celui que vous avez percé dans le mur.  
1
TROU DE ⁄ " POUR  
2
LE CÂBLAGE DU THERMOSTAT  
CORDE SOLIDE ATTACHÉE  
À UNE CHAÎNE DE 6"  
5. Attachez le câblage du thermostat à la corde et faites-le  
passer par le trou dans le mur; laissez pendre 6” de câblage.  
ENVIRON  
5 PIEDS  
PLINTHE  
TROU DE GUIDAGE  
1
DE ⁄ "  
4
QUART-DE-ROND  
ENLEVÉ  
3
TROU DE ⁄ " DANS LE PLANCHER  
4
DE LA CLOISON  
FIL DE FER REPLIÉ POUR ACCROCHER LA CHAÎNE  
Figure 1. Acheminement du câblage au site  
2
href="
7. Àl’aidedesdeuxvisdemontage, fixezlâchementlethermo-  
stat. Placez un niveau sur le thermostat et ajustez ce dernier  
pour qu’il soit de niveau. Serrez ensuite les vis pour le fixer.  
Silestrousdemontagesonttropgrandsetnevouspermettent  
pas de fixer solidement le thermostat, servez-vous des  
chevilles de plastique pour l’assujettir.  
ATTENTION  
Afindeprévenirleschocsélectriquesetlesdommages  
matériels, coupezl’alimentationélectriqueaupanneau  
dedistributionélectriqueprincipalpendantl’installation.  
8. Replacez le couvercle sur le thermostat et réglez le point de  
consigne au niveau désiré.  
NOTE  
Leschémadecâblagetypiqueillustreuniquementl’identification  
des bornes et le raccordement des fils. Pour raccorder le  
système,référez-voustoujoursauxdirectivesdecâblagefournies  
par le fabricant de l’équipement.  
9. Rétablissez le courant qui alimente le système.  
Commutateur du  
thermostat  
Tout le câblage doit être conforme aux codes et règlements  
locaux et nationaux qui régissent les installations électriques.  
Chauffage  
Bornes à vis  
INSTALLATION DU THERMOSTAT  
1. Pour détacher le couvercle du thermostat, saisissez ce  
dernier d’une main et, de l’autre, tirez doucement le haut ou  
le bas du couvercle.  
THERMOSTAT  
SYSTÈME  
Génératrice  
Flamme de  
Veilleuse  
2. Retirez soigneusement l’emballage qui protège le  
commutateur.  
Système de  
chauffage  
3. Faites passer les fils dans l’ouverture au centre du thermo-  
stat et raccordez les fils sur les bornes à vis (figures 2 et 3).  
4. Repoussez dans le mur le surplus de fil et bouchez le trou  
avec un produit ignifuge (comme de la mousse isolante en  
fibre de verre) afin d’empêcher que des courants d’air  
n’affectent le fonctionnement du thermostat.  
Figure 2. Schéma de câblage typique  
5. Placez le thermostat sur le mur, devant le trou de passage  
des câbles, et reportez sur le mur l’emplacement des trous  
de montage.  
Bornes  
à vis  
6. Percez les trous de montage.  
10  
15  
10  
15 20  
20  
25  
25  
30  
30  
THERMOSTAT  
THERMOSTAT  
COUVERCLE  
COUVERCLE  
Vis de  
montage  
Figure 3. Les parties du thermostat  
MODE D’EMPLOI ET ENTRETIEN  
ÉTALONNAGE DU THERMOMÈTRE  
DU COUVERCLE  
Si la température indiquée par le thermomètre ne correspond  
pas au réglage du thermostat :  
1. Détachez le couvercle du thermostat.  
2. Placez le couvercle sur une table près d’un thermomètre  
juste.  
3. Attendez au moins dix minutes pour que les thermomètres  
s’ajustent à la température ambiante.  
Réglage du  
thermomètre  
4. Si les deux thermomètres ne concordent pas, introduisez la  
pointe d’un petit tournevis plat dans l’axe du thermomètre,  
qui est situé à l’arrière du couvercle. Réglez le thermomètre  
du couvercle pour le faire concorder avec l’autre (figure 4).  
5. Replacez le couvrcle sur le thermostat.  
Arrière du couvercle du thermostat  
Figure 4. Étalonnage du thermomètre  
du thermostat  
3
href="
6. Placez la manette de réglage du point de consigne à la  
température de la pièce, puis détachez le couvercle du  
thermostat.  
ÉTALONNAGE DU THERMOSTAT  
Le thermostat a été réglé avec soin lors de la fabrication. Il ne  
devrait pas être nécessaire de l’étalonner.  
7
7. Glissez la clé anglaise de 32” sur l’écrou hexagonal situé  
En usage normal, les conditions atmosphériques peuvent  
entraîner une différence de quelques degrés entre le point de  
consigne et la température ambiante de la pièce. Si cette  
différenceestsignificative,assurez-vousd’abordquelethermo-  
stat est de niveau et que son emplacement a été bien choisi. Si  
l’étalonnage semble encore nécessaire, veuillez procéder de la  
façon suivante :  
sous le bilame. Tout en maintenant en place la manette,  
tournez l’écrou à gauche jusqu’à ce que le mercure se  
déplace vers la gauche du tube (figure 5).  
8. Replacez le couvercle sur le thermostat et réglez le point de  
consigne au niveau souhaité. Rétablissez le courant qui  
alimente le système.  
ATTENTION  
Afindeprévenirleschocsélectriquesetlesdommages  
matériels, coupezl’alimentationélectriqueaupanneau  
dedistributionélectriqueprincipalpendantl’installation.  
Clé de 7  
pour l’étalonnage  
32”  
Bilame  
1. Lachaleurdel’élémentanticipateurpeutaffecterl’étalonnage  
du thermostat. Dans le but d’éviter ce problème, coupez  
l’alimentation en provenance de l’appareil de chauffage ou  
du panneau de distribution électrique.  
2. Placez la manette de réglage du point de consigne environ  
à 5° au-dessus de la température ambiante.  
Manette de réglage  
du point de consigne  
3. Détachezlecouvercleduthermostat.Glissezuncléanglaise  
de 732” sur l’écrou hexagonal situé sous le bilame. Tout en  
maintenant en place la manette de régalge, tournez l’écrou  
à droite jusqu’à ce que le mercure se déplace vers la droite  
du tube (figure 5).  
4. Placez la manette de réglage du point de consigne à son  
niveau le plus bas.  
5. Replacez le couvercle du thermostat. Attendez 10 minutes  
que la température du bilame se stablise. Ne vous tenez pas  
à proximité du thermostat durant cette période, car votre  
souffle et la chaleur de votre corps pourraient affecter la  
température du bilame.  
Figure 5. Étalonnage du thermostat